SpeedTouch USB ADSL PPP Driver

admin 1/7/2022
  1. Speedtouch Usb Adsl Ppp Driver Download
  2. Speedtouch Usb Adsl Ppp Driver Free
  3. Speedtouch Usb Adsl
  4. Speedtouch Usb Adsl Ppp Driver Windows 10

The Alcatel SpeedTouch USB ADSL modem has become a popular choice for providing low cost, widely available ADSL services, particularly in the UK, where BT Ignite (a division of British Telecom) install it for use over their ADSL network. Touch™USB/330 ADSL USB modem and in getting connected quickly to the Internet. Terminology Generally, the SpeedTouch™USB and SpeedTouch™330 will be referred to as Speed-Touch™ in this User's Guide. Safety instructions Before connecting the SpeedTouch™, read the SpeedTouch™ Quick Installation Guide and Safety Instructions.

Debian Sarge HOWTO

This HOWTO is for users of the Sarge release of Debian.It was kindly contributed byGhost Dog.

The First Step: Configuring the Kernel

You will save yourself from a lot of trouble if you download thelatest kernel source.(no patching bla bla bla).

You have to be root inorder to download as well as install the programs.

Download the kernel source

apt-get install kernel-source-2.4.22

Configure the kernel

Remark: These are the options needed to get this driver running.You will also have to enable the other drivers you need for yoursystem. A good starting point to determine what these are, are the(currently) loaded modules.

For more information on how to build akernel see the Linux Kernel HOWTO.The entries required are:

  • Code Maturity Level Options
    • Prompt for development and/or incomplete code/drivers [Y]
  • Loadable Module Support
    • Enable Loadable Module Support [Y]
  • General Setup
    • Support for hot-pluggable devices [Y]
  • Networking Options
    • Packet Socket [Y]
    • Asynchronous Transfer Mode (ATM) (EXPERIMENTAL) [Y]
  • Network Device Support
    • PPP (Point-to-Point Protocol) Support [Y]
    • PPP Deflate Compression [Y]
  • USB Support
    • Support for USB [Y]
    • Preliminary USB Device Filesystem [Y]
    • UHCI (Intel PIIX4, VIA,...) Support [M]
    • OHCI (Compaq, iMacs, OPTi, SiS, ALi, ...) support [M]

For PPPoA you will need the following options:
  • Network Device Support
    • PPP Over ATM (EXPERIMENTAL) [Y]

For PPPoE you will need these options:
  • Networking Options
    • RFC 1483/2684 Bridged protocols [Y]
  • Network Device Support
    • PPP Over Ethernet (EXPERIMENTAL) [Y]

The Second Step: Installing the Binary Management Application andHotplugging

Download and install the modem_run program:

apt-get install speedtouch

Download and install hotplugging:

apt-get install hotplug

Install the firmware:

To get the firmware, follow the instructions onthis page

Next, as root, copy the firmware to /usr/local/lib:

cp mgmt.o /usr/local/lib/firmware.bin

or

cp alcaudsl.sys /usr/local/lib/firmware.bin

or

10.0.0.138 speedtouch adsl modem
cp firmware.bin /usr/local/lib/firmware.bin
Speedtouch usb adsl ppp driver downloadDriver

depending on the version of the firmware you are using.

Install the appropriate hotplug script

Place the following in /etc/hotplug/usb/speedtch:
#!/bin/bash
case $ACTION in
add)
echo 'uploading firmware'
if /usr/sbin/modem_run -k -f /usr/local/lib/firmware.bin ; then
sleep 10
echo 'starting pppd'
if ! /usr/sbin/pppd call speedtch ; then
echo 'failed to start pppd!'
fi
else
echo 'firmware upload failed!'
fi
;;
esac

The Third Step: Configuring PPPoA and PPPoE

If your provider uses PPPoA or PPPoE you will need to do
apt-get install ppp
Alcatel

Configuring PPPoA

Put the following in the file /etc/ppp/peers/speedtch:
# To connect to using this configuration file, do
# pppd call speedtch
lcp-echo-interval 10
lcp-echo-failure 3
noipdefault
defaultroute
user 'username'
noauth
noaccomp
nopcomp
noccp
novj
holdoff 4
persist
maxfail 25
updetach
usepeerdns
plugin pppoatm.so
0.38

Remarks:

You will need to replace 'username' with yourADSL username.

Also, in the above example '0.38' is the VPI/VCI ATMpair for the author's provider. You will need to know what thecorrect values are for your provider, and substitute those. If thesevalues are incorrect, you may sync, but you will not be able toconnect to your ISP's IP layer, and probably be frustrated. Thesevalues can be obtained from the Window's Alcatel client, your ISP orthe FAQ.

Edit the file /etc/ppp/chap-secrets and replace its contents withthe following:

# Secrets for authentication using CHAP
# client server secret IP addresses
username * password

Now put the same in /etc/ppp/pap-secrets.

Remark: You will need to replace 'username' withyour ADSL username and 'password' with your ADSL password.

Configuring PPPoE

Put the following in the file /etc/ppp/peers/speedtch:
# To connect to using this configuration file, do
# pppd call speedtch
lcp-echo-interval 10
lcp-echo-failure 3
noipdefault
defaultroute
user 'username'
noauth
noaccomp
nopcomp
noccp
novj
holdoff 4
persist
maxfail 25
updetach
usepeerdns
plugin pppoe.so
nas0

Remark:You will need to replace 'username' with yourADSL username.

Edit the file /etc/ppp/chap-secrets and replace its contents withthe following:

# Secrets for authentication using CHAP
# client server secret IP addresses
username * password

Now put the same in /etc/ppp/pap-secrets.

The Fourth Step: Setting up ATM

Download and Install libatm1

apt-get install libatm1

The Fifth Step: Running the driver

If everything went according to plan, the driver should start assoon as you plug in the SpeedTouch USB modem. Congratulations! You areonline!
Words shall not be hid, nor spells be buried; might shall not sink underground,though the mighty go. - The Kalevala
Speedtouch usb adsl ppp driver download

Introduction

This document explains how to set up a DSL broadband connection for people living in the UK using a Thomson Speedtouch 330 USB modem or other similar modems supported by the speedtch driver.

Speedtouch Usb Adsl Ppp Driver Download

  • ubuntu 9:10

Speedtouch Usb Adsl Ppp Driver Free

(UsbAdslModem/SpeedTouch)

Instructions

Speedtouch Usb Adsl

  • With modern kernels (>= 2.6.10) you do not need anything other than the ppp and libatm1 packages. The speedtouch package is not needed.

  • Download the modem firmware from the Alcatel web site (site down - mirror to zip) and unpack it with the firmware extractor. If this looks complex, you can just download and install an unofficial firmware package

speedtouch-firmware.tgz or speedtouch-firmware_0.1-7_all.deb.

  • Firmware (speedtch-*.bin.4) for the (silver) revision 4 modem.

or

  • After installing the firmware you may unplug and replug the modem to load it.
  • Copy the /usr/share/doc/ppp/examples/peers-pppoa file to e.g. /etc/ppp/peers/adsl. The following command will preform this action:
  • Edit with

(or for Kubuntu)

to include the username given to you by your isp and the VP and VC identifiers 0.38 (Poland, TPSA neostrada tp 0.35) (they may differ for other ISPs).

  • Edit the

(or for Kubuntu)

file (in /etc/ppp/) and update them with the username and password provided by your isp by adding to each a line in the format

and/or

  • After the boot, you will be able to start the connection with the usual commands

Speedtouch Usb Adsl Ppp Driver Windows 10

  • (FIXME: document how to create an udev script to automatically start the connection after the modem has been initialised.)